HCPL3120 DATASHEET PDF

HCPLE from Avago at low prices and same day dispatch! Orders above £20 Technical Datasheet: HCPLE Datasheet. See all Technical. Sat, 10 Nov GMT hcpl j hcnw 2 pdf – Avago. Technologies – 2 -. HCPL/J,. HCNW Data Sheet. Functional. Diagram. HCPL datasheet, HCPL circuit, HCPL data sheet: HP – Amp Output Current IGBT Gate Drive Optocoupler,alldatasheet, datasheet.

Author: Tulrajas Kajas
Country: Yemen
Language: English (Spanish)
Genre: Music
Published (Last): 2 February 2004
Pages: 216
PDF File Size: 6.11 Mb
ePub File Size: 17.81 Mb
ISBN: 808-4-19278-430-1
Downloads: 33757
Price: Free* [*Free Regsitration Required]
Uploader: Daikree

Documents Flashcards Grammar checker.

The LED is optically coupled to an integrated circuit with a power output stage. The high operating voltage range of the output stage provides the drive voltages required by gate controlled devices. Contact an Avago Technologies sales representative or authorized distributor.

To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Option data sheets are available. Contact your Avago Technologies hcpp3120 representative or authorized distributor for information.

Minimum External Tracking L Creepage 7. These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements.

However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards. For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered.

HCPLE – Avago Technologies – PCB Footprint & Symbol Download

There hdpl3120 recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. Maintenance of the safety data shall be ensured by means of protective circuits. See Applications section for additional details on limiting IOH peak.

  AKG C547BL PDF

HCPL Datasheet(PDF) – Agilent(Hewlett-Packard)

In this test, VOH is measured with a dc load current. Pins 1 and 4 need to be connected to LED common. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Broadcom Ltd. Device considered a two-terminal hcpl3102 Temperature Figure 3 VOH vs.

This results in lower peak currents more margin than predicted by this analysis. When negative gate drive is not used VEE dataseet the previous equation is equal to zero volts. The thermal resistance values given in this model can be used to calculate the temperatures at each node for a given operating condition. However, this shield does not eliminate the capacitive coupling between the LED and optocoupler pins 5—8 as shown in Figure This capacitive coupling causes perturbations in the LED current during common mode transients and becomes the major source of CMR failures for a shielded optocoupler.

Techniques to keep the LED in the proper state are discussed in the next two sections. This is achieved by overdriving the LED current beyond hvpl3120 input threshold so that it is not pulled below the threshold eatasheet a transient.

  FFX-2 PIGGYBACK GUIDE PDF

Cheap hcpl 3120 datasheet deals

Figure 33 is an alternative drive circuit which, like the recommended application circuit Figure 25does achieve ultra high CMR performance by shunting the LED in the off state. Dead time is the time period during hcp3120 both the high and low side power transistors Q1 and Q2 in Figure 25 are off. Any overlap in Q1 and Q2 conduction will result in large currents flowing through the power devices between the high and low voltage motor ucpl3120.

To minimize dead time in a given design, the turn on of LED2 should be delayed relative to the turn off of LED1 so that under worst-case conditions, transistor Q1 has just turned off when transistor Q2 turns on, as shown in Figure Delaying the LED signal by the maximum propagation delay difference ensures that the minimum dead time is zero, but it does not tell a designer what the dahasheet dead time will be.

Note that the propagation delays used to calculate PDD and dead time are taken at equal temperatures and ratasheet conditions since the optocouplers under consideration are typically mounted in close proximity to each other and are switching identical IGBTs.

(PDF) HCPL-3120 Datasheet download

All other brand and product names may be trademarks of their respective companies. Data subject to change. AVEN — Hpcl3120 21, Lab 9 in this note.