BC558C DATASHEET PDF

BCC datasheet, BCC pdf, BCC data sheet, datasheet, data sheet, pdf, Boca Semiconductor Corporation, 30 V, PNP silicon planar epitaxial transistor. BCC Transistor Datasheet pdf, BCC Equivalent. Parameters and Characteristics. BC Silicon PNP Transistor. Audio Amplifier, Switch. Features: D Suitable for AF-Driver Stages and Low Power Output Stages. Absolute Maximum Ratings.

Author: Vuzil Muk
Country: Comoros
Language: English (Spanish)
Genre: Travel
Published (Last): 26 August 2004
Pages: 199
PDF File Size: 3.50 Mb
ePub File Size: 9.28 Mb
ISBN: 416-8-27866-785-5
Downloads: 5930
Price: Free* [*Free Regsitration Required]
Uploader: Mazuru

Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. BC is a general purpose PNP transistor. When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. A Transistors acts as an B5c58c when operating in Active Region.

BCC Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

In the absence of base signal, it gets completely off. SPI Module of Arduino. BC has a gain value of to ; this value determines the amplification capacity of the transistor. What is Web Dahasheet. BC is used in common emitter configuration for amplifiers. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. It is also used as a complement for transistors BC to BC Amplifier modules like Audio amplifiers, bc558x Amplifier etc.

The value of this resistor RB can be calculated using below formulae. A resistor is always added in series with base pin to bc558d the base current.

  LAURIE HELGOE INTROVERT POWER PDF

Transistor BC558

Skip to main content. It is used in switching and amplifier applications. This high-density System-in-Package SiP integrates controller, power switches, and support components.

Choosing Battery for Robots. The input signal at base is amplified and taken at the emitter. This is known as the biasing. In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal.

BC Pinout, Configuration, Circuit As Switch & Amplifier

BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin. The BC because of this large gain value is normally used to as a audio amplifier. For amplification applications, the datasueet is biased such that it is partly on for all input conditions. It can amplify power, voltage and current at different configurations.

The voltage divider is the commonly used bc558cc mode.

Submitted by admin on 26 March Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched. Virgin Galactic — Commercial Space Flight. Choosing Motor For Robots.

  GRAHAN KAND PDF

When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

The DC current gain varies in range to Interface SD Card with Arduino. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves.

As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

BC558C Datasheet, Equivalent, Cross Reference Search

Arduino based GPS receiver. TL — Programmable Reference Voltage.

Interface GPS with Arduino. Complete Technical Details can be found in the BC datasheet given at the end of this page.

For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.